Rules at the bench
- Run the fume extractor within 10–20 cm of every solder joint.
- Wash your hands after soldering. No food or drink at the bench.
- Keep the printer enclosure closed while printing and for 15–30 minutes after.
- Check the monitor's CO₂. Above 1,000 ppm, open the air path or take a break outside.
- Don't sit next to an ABS or ASA print. Start it, leave, and come back.
The air quality monitor
The makerspace has a Qingping Air Quality Monitor 2. It measures PM2.5, PM10, CO₂, eTVOC,
noise, temperature and humidity, and keeps 30 days of history in the Qingping+ app. For soldering and printing,
watch these three:
| Reading | Threshold | What it tells you |
| CO₂ | ~1,000 ppm (Japanese building standard) |
The best sign that the room is barely exchanging air, so fumes are building up. |
| PM2.5 | 35 µg/m³ (Japan daily standard) 15 µg/m³ (WHO guideline) |
Catches solder flux smoke well. Undercounts 3D-printing particles (see below). |
| eTVOC | 400 µg/m³ (MHLW provisional target for total VOCs) |
Printing and flux vapours. An estimate, so treat it as a trend rather than an exact value. |
Watch for spikes against your baseline rather than absolute values. Note the readings in an
empty room, then see what changes when you start soldering or printing.
What the monitor can't see. 3D printers emit mostly ultrafine particles, smaller than 0.1 µm.
Laser PM sensors at this price start detecting around 0.3 µm, so they undercount printing emissions.
A low PM2.5 reading during a print does not mean the air is clean.
What reduces exposure, most effective first
1. Capture fumes at the source
This matters far more than cleaning the room air.
- Soldering: use a fume extractor (はんだ吸煙器) with both a HEPA filter and activated carbon.
HAKKO is the standard Japanese brand. Check the filter spec: some models are carbon-only and let fine
particles through.
- 3D printing: enclose the printer and run a small HEPA + carbon filter inside the enclosure.
Emissions peak when a print starts and continue while parts cool.
2. Choose lower-emission materials and settings
- PLA emits far less than ABS/ASA, which release styrene. PETG sits in between.
- Print at the low end of the recommended nozzle temperature. Emissions rise sharply with heat.
- Use no-clean or low-fume flux. Rosin (colophony) fume is a known cause of occupational asthma.
Sensitisation builds with repeated exposure, so "it doesn't bother me yet" means nothing.
- Resin (SLA) printing is a different hazard: VOCs plus skin sensitisation. Wear nitrile gloves,
and never use it in an unvented room without an enclosure.
3. Filter the room air
Run a HEPA purifier with a real carbon bed while you work and for an hour after. Typical home
purifiers have thin carbon layers that absorb little VOC; a unit with a heavy carbon filter does better
against printing odours.
4. Find a path to outdoor air
Look for a 24時間換気 vent, an exhaust fan you can run, or a gap under the door, and put the printer next to it.
A cheap duct-fan exhaust through a vent hole is worth more than any filter. The CO₂ reading shows whether
it's actually moving air.
5. Manage your own exposure
- Lead solder: lead doesn't meaningfully vaporise at soldering temperatures. The risk is
hand-to-mouth contact, so wash your hands and don't eat at the bench.
- Heavy sessions: wear a half-face respirator with P100/P3 filters plus organic-vapour
cartridges (防じん・防毒マスク, e.g. 3M 6000 series or Shigematsu).
A DS2 or N95 mask stops particles but does nothing for VOCs.